How To Install a Privacy Fence

Your home’s exterior design can be influenced by fencing.Adding fencing to your home increases its value and aesthetic appeal.It protects children and pets.It gives character and depth to your home and is an asset.There are many options for every budget and taste.There is a guide on how to install a wood privacy fence, as well as other options.

Step 1: Check the neighborhood rules.

It is important to determine if you can build a fence at all.You can be fined and have to tear the whole thing down if you build one in an unauthorized way.If you want to build a fence, make sure you check your local neighborhood rules or homeowner’s association rules.If your neighbor is willing to share the cost of the fence with you, then you should talk to them.

Step 2: Check the city codes.

There are rules about building fences in cities.Before building one, you need to check what they are.Some cities require a permit to build a fence above a certain height.Find out if you need a permit or if there are other restrictions on the building.

Step 3: Obtain a permit.

You should get a permit before you start building.These can be obtained from your local Planning Department or City Hall.Before you start digging, make sure to call the Digline.

Step 4: Pick your materials.

You have to decide what kind of fence you want.Different types of materials have different benefits and drawbacks.How much time you want to spend on upkeep, how much money you have to invest, and how long the fence will need to remain in its location will all be considered.It’s the most common.These last between 5 and 20 years depending on the type of wood, and are relatively inexpensive.If they get paint on them, it will be difficult to clean them.If you use quality vinyl, it will last up to a lifetime.They can come in a variety of colors that will not fade over time and are easy to clean.In terms of upfront costs, they are slightly more expensive.If you don’t like the look of wood or vinyl, or if you need something more sturdy, it’s an option.You can use concrete block or brick.A “Southwestern” look can be achieved by covering the concrete block with cobble or plaster.Concrete blocks can be turned to create planters.Masonry will be more expensive than other options, but it will last longer than wood.If your city is very restrictive about permits, they are a great option.If you prefer more greenery in your yard, they are good.You can plant arborvitae, an evergreen shrub which grows three feet a year, put in an iron or chain fence and train ivy, or grow more standard hedges like holly.

Step 5: Post locations can be found.

Measure and mark the locations of the intermediate posts, as well as the perimeter of your fence, using string tied to stakes.The normal spacing between posts is 8 feet from center to center.All locations should be marked with spray paint or stake holes.

Step 6: Post holes should be dug.

You can use a post-holer to dig holes up to 13 the height of the fence.Many cities have rules regarding hole depth, so make sure you follow the rules in your permit.You do not want to hit a water main.Remember to call the Digline before you dig.Water mains are usually placed at least 4 ft in the ground so a deep posthole should be safe.There are two ways to use a digger, a manual one and a motorized one.You can rent both from your local hardware store.

Step 7: Place gravel outdoors.

To make sure the posts don’t rot, you will want to put a few inches of gravel in the bottom of the hole.

Step 8: Put posts.

Use 4×4 posts at your preferred height and place them one at a time.This may require some assistance.It is more labor intensive to vary the depth of the hole to keep the posts the same than it is to cut off the top of them after 24 hours.The tops of posts need to be sealed to protect them from rain damage.

Step 9: Put it in quick-set concrete.

To make sure the post is plumb, double check the height and use a post level.Continue to use the level as it sets to be sure that it stays straight after pouring in the concrete and mixing with water according to the manufacturer’s instructions.You can mix the concrete in a bucket or wheelbarrow.Continue to use string to make sure the posts are in line.

Step 10: Continue to set posts.

Before moving on, get in all the posts.Cross bracing can be used to hold posts in place.It will take at least 24 hours.

Step 11: Cut your rails.

The boards are set between the posts.The rails will be attached to the main boards of the fence.They should be cut to fit between the posts.Depending on the height of your fence, you will need two or three rails.

Step 12: The rail frame needs to be created.

Take a 1×4 and cut it to the same height as the posts.If you want your rails to go, mark the spots on the board.Put the 1×4 flat to the end of the top and bottom rails.The rails should be 90 from the 1×4 board and look like a T.For each end of the rail, do this.

Step 13: Attach the frame.

Attach the frame in between the posts with deck screws.The fence should be rust proof to prevent it frombleed over time.

Step 14: Attach pickets or slats.

slats or pickets should not be more than 1” thick.To ensure that they are even and that the space between them is less than their width, use 2” screws or nails to nail or screw them into the rails.Continue the length of the fence.

Step 15: Attach the pickets.

Attach the boards on the inside of the fence.The gaps created by the outside boards should be covered by these.

Step 16: Add a gate.

You can either add a fence gate to the yard or not.Follow the instructions to add a gate.

Step 17: There are finishing details.

You can paint or stain your fence as you please.There are shrubs planted along the baseline.