How To Cut Copper Pipe

Home repair and design use copper pipe.It’s easy to cut with this lightweight material.You can attach an autocut tool for pipes under 1 inch.The tool can be turned around to make a clean cut.You can attach a tubing cutter to the pipe.As you rotating the cutter around the pipe, tighten it.You can always use a hacksaw if you don’t have the tools.sawing the pipe won’t give you as precise a cut as you might think.

Step 1: An autocut tool can be selected.

If you’re cutting copper pipe in a tight space, use an autocut tool.Purchase an autocut tool for the exact diameter of the pipe you want to cut.You won’t be able to adjust the size of the cut because the autocut tools are spring loaded.For a 1/2 inch (12mm) pipe, buy an autocut tool.There are three sizes of autocut tools: 1/2 inch (12mm), 1/3 inch (19mm) and 1 inch ( 2.5 cm).

Step 2: The copper pipe has an autocut tool on it.

The pipe should be placed in the center of the autocut tool.The gray clamp needs to be secured onto the pipe.The tool should not allow the pipe to wiggle or slide out.

Step 3: The tool should be turned 20 to 30 times.

The arrow on the tool tells you which way to turn it.Hold the pipe with one hand and use the other to turn the tool.The tool should be turned 20 to 30 times.You won’t need to clean the pipe before using the auto cut tool.

Step 4: The cutter should be secured to the pipe.

The jaws of the tubing cutter can be opened with the handle.If you want to make the cut, place the copper pipe in the jaws.To tighten the jaws, spin the handle.The tubing cutter is used to hold the pipe to the blade.

Step 5: It’s a good idea to score the pipe lightly.

Hold the pipe with one hand and use the other to move the handle around.There is a faint line around the pipe that was cut lightly by the blade.As you cut into the pipe, this line will be a guide.

Step 6: Turn the cutter.

Continue to move the handle of the tool around the pipe to keep the blade from cutting into it.If the blade is cutting into the same line, it won’t go down the pipe.You can tighten the cutter with the small knob on the base of the tool.The blade will stay on the same track.

Step 7: Pull away the pipe with the cutter.

Set the tubing cutter aside.You should be able to hold both ends of the pipe.The cut portion should be snapped away by bending the pipe.You should see a clean cut.To make a clean cut through the pipe, use the tubing cutter.

Step 8: Pick the right blade.

To cut through the copper pipe, use a hacksaw with a small gap between its teeth.A hacksaw with a 32-TPI blade has the shortest distance between the teeth.The hacksaw can get stuck on the pipe if the gap between the teeth is too large.

Step 9: Attach the copper pipe.

If the pipe is loose, set it in a vise so that the spot you want to cut extends a few inches from the jaws.This will allow you to cut.The handle should be spun until the pipe is secured.If you’re using a thin pipe, you may need to spin the handle a lot.

Step 10: The copper pipe needs to be marked.

Determine where you want to cut the copper pipe.Take a permanent marker and draw a line.You can use rubbing alcohol to wipe the mark off after you’ve cut the pipe.

Step 11: The hacksaw blade should be on the mark.

Place the hacksaw’s teeth on the mark you made.Hold the handle of the hacksaw with your dominant hand and use your other hand to support the saw top.

Step 12: Saw into the pipe.

As you bring the hacksaw back towards you, move the blade firmly across the pipe.Push the saw blade into the pipe until the cut piece falls off.If you are sawing in a backwards and forwards motion, you could damage the blade or make a ragged cut on the pipe.

Step 13: The cut copper pipe needs to be cleaned.

The cut pipe can be cleaned with a 4-in-1 cleaning tool.Place the center circle of the tool around the pipe itself and use the ends to brush inside it.Rub the end of the tool to make it easier to clean the pipe.It is possible to cut a piece of sandpaper into a 1 in by 5 in strip.Wrap it around the pipe and pull it back and forth.