Ceiling tiles should be installed.

Ceiling tiles can change the look of a room if you want a simple update.When coupled with a unique molding, decorative tiles can give a subtle boost to the room’s décor.Depending on the type of tiles, they can suppress noise and insulate the ceiling.Basic skill with household tools is required.You can apply tiles to the ceiling if it is in good shape.Furring strips can be added to give the tiles the foundation they need.You’ll be surprised at the difference ceiling tiles make to your room.

Step 1: The ceiling needs to be cleaned.

If the ceiling is not very dirty, you can simply use a broom to clean it.If your ceiling is dirty or greasy, use a sponge to scrub one small section at a time using an all-purpose cleaner.It’s important to dry the ceiling before applying tiles.A clean surface will make your tiles stick better.If the ceiling is dirty or peeling, you may have trouble attaching them.If your ceiling is greasy, you can wash it with a mixture of 1 cup ammonia and half a gallon of water.

Step 2: Take the square footage of the room.

To record how long the ceiling is, use a measuring tape.Measure how wide the ceiling is.You can get your square footage by using these two numbers.If your ceiling is 12′ long and 15′ wide, the square footage is 180.

Step 3: Determine the number of tiles you need.

You have to figure out the square footage of each tile.To get the tile’s measurement, divide the length times the width.Divide the ceiling by the square footage of one tile.This will let you know how many tiles you need.The square footage for the tile is divided by 2 to get the total.Divide your room’s square footage by four.You will need at least 45 tiles.You should always buy more tiles than you think you need.If you need to cut tiles or make a mistake, you’ll have plenty to complete the job.

Step 4: The fixture or vent should be removed.

Remove the light fixture, fans, or air vent covers.It will allow you to easily measure and install tiles.You should use a flat-head screwdriver to remove the fixture.It is a good time to clean the fixture and vent.

Step 5: The center of the room can be found by using chalk lines.

Measure halfway across each wall in opposite directions, using the length and width measurements you made for the ceiling.While you walk to the opposite end of the room, have someone hold the chalk line or reel.The ceiling has chalk against it.Do the same for the two walls.If your room was 15′ wide and 12′ long, you should measure 6′ across the length of the room.The center of the room should have 2 straight lines that cross each other.This is where you will start laying tiles.

Step 6: You can apply cement or glue to your tiles.

The back of your tiles should be spread with a foam brush or a putty knife.The four corners of the ceiling tile need to be spread with 1 inch (2.54 cm) from the edges to the center.Determine the correct cement or glue for your tile material by checking package instructions.

Step 7: The tiles need to be applied to the ceiling.

The two chalk lines meet in the center of the room.Make sure it is level and aligned by pressing it against the ceiling.Place the tiles from the center until you reach the other side of the room.The chalk lines can be used as a guide.

Step 8: Cut tiles.

Measure the size and shape of the fixture hole and find out where it will be on the ceiling tile.Measure the hole and cut it with straightedge or scissors.Put the tile on the ceiling where the fixture will be.Before adhering your cut to the ceiling, do a dry run and test it.Make sure the hole is completely visible by holding your tile up over it.This will allow you to easily remove the fixture.

Step 9: Measure and cut tiles.

When you’re tiling your ceiling, you may notice that the tiles don’t fit completely, because you are near the edges.Measure the tile size for the edges.Use a straight edge to cut the tile, apply glue, and press the edge tile against the ceiling.This should be done around all the edges.Before adhering your cut to the ceiling, do a dry run and test it.Hold the tile against the edge of the ceiling.It shouldn’t be too tight or hard to apply.

Step 10: Attach the mold to the borders.

Attach the molding to the wall with a staple or nail gun if you want to add borders.The holes should be filled with wood filler and painted.It can make your room look better.It can hide the edges of tiles that have been cut.

Step 11: There is one of the joists.

Structural support is provided by a length of timber or metal.It’s easy to find them in the ceiling with a stud finder.Place a nail or chalk mark on the spot.Since they’re installed along joists, you might want to check for them first.

Step 12: The other joists can be found.

Check for the presence of the next one by measuring 16 inches from the first one.The Joists are usually 16 inches to 24 inches (40.64 to 60.96 cm) apart, so you should find it close to those measurements.The joists are visible across the entire ceiling with a chalk line.

Step 13: The furring strips need to be installed.

Furring strips are thin strips of wood that you attach at a right angle to your joists so that they are flush against the wall.The nail is stapled into the strip.Make sure the furring strip is level.If it isn’t, add a shim to make it level.If you want your furring strips to fall through the center of your tiles, make sure they are at even intervals.As you install the furring strips, you may want to hold up tiles for reference.

Step 14: The first tile should be put in the corner.

The first strip is closest to the wall.Align the corner tile with the line and the wall, then staple it to the furring strip using at least 2 staples along the sides and 1 in each corner.Continue putting edge tiles.

Step 15: Once you’ve stapled the tiles across the ceiling, you can fill in the rest with whole tiles.

To fit a tile around a fixture, you may need to use a straight edge.Measure the size and shape of the fixture hole and find out where it will be on the ceiling tile.Measure the hole and cut it.

Step 16: Attach the molding to the borders.

Attach the molding to the wall with a staple or nail gun if you want to add borders.The holes should be filled with wood filler and painted.It can make your room look better.It can hide the edges of tiles that have been cut.